#ICOM IC7300 AND FLDIGI SETUP HOW TO#
#ICOM IC7300 AND FLDIGI SETUP FOR MAC#
#ICOM IC7300 AND FLDIGI SETUP INSTALL#
#ICOM IC7300 AND FLDIGI SETUP MOD#
#ICOM IC7300 AND FLDIGI SETUP SERIAL#

It should go from red to black lettering. It's better to choose a fixed baud rate than Auto. Verify that the Baud rate in flrig matches the baud rate selected in the rig.

#ICOM IC7300 AND FLDIGI SETUP SERIAL#

Open the device manager and determine to which com port the serial driver from Silcon Labs is assigned and choose that from the drop down list. fldigi doesn't support using the 7300's internal keyer via hamlib commands, unfortunately. There will be a message on the General page if it has been blocked. Either use USB-D mode with fldigi's audio CW keying, or use an external CW keyer ('Winkeyer' support, although there are actually lots of compatible devices).

#ICOM IC7300 AND FLDIGI SETUP INSTALL#

If you're using MacOS High Sierra or a later version of MacOS you may need to authorize the driver install in Security & Privacy setup in System Preferences after runing the install program. It if still isn't in the list then the driver is not loading for some reason like the radio is not on or connected or the driver has not been installed properly so that needs to be rectified before going on. If the device does not appear in the list then click the SerPort button to repopulate the list. Mac/Linux - Select the SilconLabs driver from the dropdown list. Note: The RTS +12v and DTR +12v boxes do not need to be selected. That will select the default settings which will be good for starters. It will come up with just a basic display.Ĭhoose the 7300 from the Rig dropdown list. With the radio on and the USB cable connected and no other communications program running, Start flrig.

#ICOM IC7300 AND FLDIGI SETUP FOR MAC#

For Mac and Linux install them as you would any other application. Putting them in other folders can causes permissions issues sometimes on Windows 10. You should have already installed the driver for the built-in sound card in the 7300.Ĭonnect the transceiver to the computer with a USB A-Male to B-Male cable and turn on the radio.įor Windows flrig will install to it's own folders and should be installed in the normal application folder where other applications are installed. Response will be a bit quicker with higher rates, but it will do well at 19,200 also. I use 115,200, but use 19,200 for starters as that is what flrig defaults to. Many of these are ok at default, but verify the ones listed below:ĬI-V USB Baud Rate - 19,200. Once the above are set then touch the CI-V line on screen to get a list of items to set especially for CAT control. See the fldigi manual on setting up the sound levels. Something to play with to make it work best for you. Too much and you overdrive fldigi and decoding suffers, too little and you may miss weak signals though fldigi does very well with very weak signals. This is the built-in soundcard in the radio output level that goes into fldigi on receive.

#ICOM IC7300 AND FLDIGI SETUP HOW TO#

How to fine tune it will be explained later.ĪCC/USB AF Output level - I have mine set at 80%. This is the input level control for the TX sound from the computer.

#ICOM IC7300 AND FLDIGI SETUP MOD#

USB MOD Level - I have mine set at 28% so you might try this for starters. I won't delve into CW or RTTY (FSK) in this post.

The settings in this article will work with all of the major digital modes that I have tried. Whether using RTTY (AFSK), BPSK, JT65, JT9 or FT8, this is a fun and easy digital mode transceiver to operate. This applies only when the rig is not in data mode. Consistency I try to keep my settings the same for all of my software.

Make sure the settings for these items are as follows:ĭata Off Mod - Mic, ACC or just Mic if you wish. Setup for the 7300 for two data connections is covered in our user guide. Providing its an FTDI chip you should not have a problem, you could try the ZLP Electronics one which we know to work and Neil ships to the US. Try it.Press the transceiver MENU button then the on screen items: Set, then Connectors. Re: CI-V to USB Cable for the IC-7300 fldigi solution. Change it to 94 for the IC-7300.įor Icom 7610 rig control choose the correct Com Port, Baud Rate and change the Command to Read Frequency CI-V address to 98, Don't forget the other side, Command To Read Mode. Just change the CI-V address in ACLog under Rig Interface to 98 for the IC-7610. Especially if you are replacing a previous radio. It's easy to configure N3FJP's Amateur Contact Log for the Icom IC-7610. Icom 7610 Rig Control Using N3FJP Amateur Contact Log Currently Flrig, HamLib and RigCAT do not have files for the Icom 7610. Wow, what a great combo!Īs of the writing of this post, Icom 7610 owners have to look at rig control alternatives for the Icom IC-7610. Amateur Contact Log is easy to configure for the Icom 7610 and Fldigi integrates with it beautifully! Fldigi logs right into AC Log. Icom 7610 rig control problems? Having trouble finding software for the Icom 7610? If you are a fan of N3FJP software and Fldigi then this is for you.

Icom ic7300 and fldigi setup